|
|
| PHONO PREAMPLIFIER |
The phono preamplifier is suitable for moving magnet and high-output moving coil cartrdiges |
| Input Impedance |
47 k |
Input Capacitance
|
100 pF |
| Maximum Input |
18 mV at 20 Hz, 140 mV at 1 kHz, 160mV at 20 kHz |
| Gain (at 1 kHz) |
35 dB |
| Crosstalk (at 1 kHz) |
80 dB |
| RIAA Response |
+/- 0.5 dB (100 Hz to 20 kHz); -1 dB (20 Hz) |
| THD+N (at 1 kHz, 5 mV input) |
0.05% |
| S/N Ratio (ref. 5 mV at 1 kHz, IEC-A filter) |
83 dB |
PREAMPLIFIER
|
| Input Impedance |
30 k |
| 'Pre-Out' Output Impedance |
560 |
| 'Rec-Out' Output Impedance |
100 |
| Rated Input |
1.0 Vrms |
| Maximum Input |
7.6 Vrms |
| Minimum Load |
5 k |
| Rated Output (100 k load) |
1.0 Vrms |
| Maximum Output (100 k load) |
7.6 Vrms |
| Headphone Output |
500 mW into 32 at 0.03% THD+N |
| Channel Separation (at 1 kHz) |
75 dB |
| Crosstalk Between Inputs (at 1 kHz) |
72 dB |
| XLR Pin Configuration |
Pin 1: Ground; Pin 2: Positive; Pin 3: Negative |
| Frequency Response and Bandwidth |
20 Hz to 20 kHz (+0, -0.1 dB); 1 Hz to 170 kHz (+0, -3 dB) |
| THD+N (at rated input and output, 80 kHz BW) |
0.003% |
| IMD (CCIF at 15 kHz and 16 kHz) |
0.0005% |
|
|
| S/N Ratio (A-weighted, ref 2.0 Vrms) |
105 dB |
| POWER AMPLIFIER |
| (per channel, continuous RMS, 20 Hz to 20 kHz, <1.0% THD) |
| Impedance |
¥ |
8 |
|
4 |
|
| # of Channels Driven |
1 |
Both |
1 |
Both |
| *Short Term |
240 W |
225 W (FTC) |
330 W |
310 W* |
|
|
|
| Frequency Response |
20 Hz to 20 kHz (+0, -0.15 dB) |
| Bandwidth |
1 Hz to 200 kHz (+0, -3 dB) |
| THD+N |
0.01% at 1 kHz, 0.03% at 20 kHz (100 W into 8 ) |
| Power Bandwidth |
< 10 Hz to 100 kHz (+0, -3 dB, 200 W into 8 ) |
| Slew Rate |
25 V/µs |
| Headroom |
1.4 dB (8 ), 2.8 dB (4 ) |
| Damping Factor |
80 at 1 kHz (ref. 8 ) |
| S/N Ratio (A-weighted, ref 225 W) |
105 dB |
| Crosstalk |
> 57 dB (100 Hz to 10 kHz) |
| Voltage Gain |
29 dB |
| CONTROL |
| Infra Red |
Carrier Frequency |
38 kHz |
| |
Max. Emitter Current |
Pass-through of input |
Trigger
|
Input Polarity |
Non-polarized |
| |
Output |
Pass-through of input |
| POWER REQUIREMENTS |
| Power Consumption (8 load) |
| |
Maximum |
800 W |
| |
Typical |
300 W |
| Fuse Rating (Fuse is internal) |
Anthem serviceable only |
| Low Voltage Version: In countries where the line voltage is 120V, this product operates from a single phase AC power source that supplies between 108V and 132V at a frequency of 60 Hz. |
| High Voltage Version: In countries where the line voltage is 220V, 330V or 240V, this product operates from a single phase AC power source that supplies between 216V and 264V at a frequency of 50 or 60 Hz. |
| Dimensions |
| Height |
5-7/8 inches (14.9 cm) including feet |
| Width |
17-1/4 inches (43.8 cm) |
| Depth |
18 inches (45.7 cm) |
| Weight (Unpacked) |
42.6 lb (19.4 kg) |
| Advanced Load Monitoring (ALM) |
| Anthem® integrated amplifiers are designed to perform flawlessly - offering stunning musicality, tonal |
| neutrality and incredible dynamics while driving any speaker load reliably under real-world conditions! The |
| power supply is conservatively rated and the amplifiers run cool for greater reliability, but we didn't stop there. |
| These amplifiers feature our ALM (Advanced Load Monitoring) circuitry which protects sensitive output |
| devices by constantly monitoring temperature, current and voltage to ensure optimum long-term performance. |
| ALM is totally non-invasive - it is not in the signal path and only engages in the most extreme circumstances |
| to protect the amplifier from damage by maintaining the safe operating area of the output devices. Buyer |
| beware however! Not all amplifier manufacturers have sophisticated load-monitoring provisions. Many have |
| saved the added cost, leaving their output devices unprotected, choosing instead to use the amplifier's output |
| devices as "fuses." At Anthem, ALM is just one of the ways in which our products provide owners with years of reliable service. |
|
|
|
|
|
|
|
|
