onMenu
onTab
Nav
Main
Footer
Total
Window

D2v 3D

» D2v Series » A/V Processor

$9,499 each USD 



D2v 3D Specifications

VIDEO SWITCHING
Bandwidth from input to output jack (bypass mode for component video)
Composite and S-Video 70 MHz
Component Y 110 MHz
Pr 90 MHz
Pb 80 MHz
All analog video inputs and outputs are 75 Ω, 1.5 Vp-p.
ANALOG AUDIO
Input Impedance 20 kΩ
Output Impedance Main-RCA 300 Ω
XLR 600 Ω

Zones 2/3 and Record 51 Ω
Rated Input 2.0 Vrms
Maximum Input 5.3 Vrms
Minimum Load 5 kΩ
Rated Output (100 kΩ load) 2.0 Vrms
Maximum Output RCA 6.3 Vrms
XLR 12.6 Vrms
Headphone Output 100 mW into 32 Ω at 0.2% THD+N
Volume Control Range Main - 95.5 dB to +31.5 dB (in 0.5 dB increments)
Zone 2/3 and Headphone - 62.5 dB to +10.0 dB (in 1.25 dB increments)
Crosstalk (at 1 kHz) 82 dB between channels; 86 dB between inputs
XLR Pin Configuration Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
DIGITAL AUDIO
Crossover High-Pass Slope (small speaker setting) 12 dB/octave (2nd order)
Low-Pass Slope (subwoofer) 24 dB/octave (4th order)
Frequency (adjustable) 25 Hz to 160 Hz (in 5 Hz increments)
Tone Control Fliter Type Shelf
Range +/- 12 dB
Bass Turnover Frequency 200 Hz
Treble Turnover Frequency 2 kHz
Analog-to-Digital Conversion S/N Ratio (at digital Rec output) (IEC-A Filter) 100 dB
All digital audio inputs and outputs comply with HDMI, S/PDIF or AES/EBU standards. Sample rate converter output is 24 bit/192 kHz regardless of input.
MAIN PATH (RCA and XLR Outputs)
Frequency Response and Bandwidth Analog Direct Inputs 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 130 kHz (+0 -3 dB)
Analog-DSP Inputs at 24/96 10 Hz to 20 kHz (+0 -0.3 dB), 2 Hz to 44.1 kHz (+0 -3 dB)
Digital Inputs at 24/96 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 45 kHz (+0 -3 dB)
THD+N (at Rated Input and Output) Analog Direct Inputs 0.006% (80 kHz BW)
Analog-DSP Inputs at 24/48 or 24/96 0.004% (AES17 Filter)
Digital Inputs at 24/48 or 24/96 0.004% (AES17 Filter)
IMD (CCIF at 15 kHz and 16 kHz) Analog Direct Inputs <0.001%
Analog-DSP Inputs at 24/48 0.001%
Digital Inputs at 24/48 or 24/96 0.001%
S/N Ratio (ref. 2.0 Vrms, IEC-A Filter) Analog Direct Inputs 107 dB
Analog-DSP Inputs at 24/48 or 24/96 101 dB
Digital Inputs at 24/48 or 24/96 104 dB
ZONE 2 and ZONE 3 PATHS
Frequency Response and Bandwidth 20 Hz to 20 kHz (+0 -0.1 dB), 3 Hz to 140 kHz (+0 -3 dB)
THD+N (at Rated Input and Output) 0.06% (80 kHz BW)
IMD (CCIF at 15 kHz and 16 kHz) 0.06%
S/N Ratio (ref. 2.0 Vrms, IEC-A Filter) 97 dB
FM TUNER
Sensitivity 50 dB S/N 13 dBµ typical, 25 dBµ max.
IHF 10 dBµ typical, 20 dBµ max.
S/N Ratio Mono 75 dB typical, 65 dB min.
Stereo 69 dB typical, 60 dB min.
Distortion Mono 0.2% typical, 1.0% max.
Stereo 0.3% typical, 1.5% max.
Stereo Separation 40 dB typical, 25 dB min.
Alternate Channel Selectivity (+/- 400 kHz) 70 dB typical, 60 dB min.
Frequency Response 25 Hz to 15 kHz (+0 -2 dB)
AM TUNER
Sensitivity (20 dB S/N) 49 dBµ typical, 56 dBµ max.
S/N Ratio 50 dB typical, 43 dB min.
Distortion 0.7% typical, 2.0% max.
One-Signal Selectivity (+/- 10 kHz) 24 dB typical, 18 dB min.
CONTROL
Infra Red Carrier Frequency 38 kHz
Maximum 12 V Supply Current 150 mA
Maximum Emitter Current 60 mA per output
RS-232 Interface Connection DB-9F, straight-wired
Pinout (D2v side) Pin 2: Tx, Pin 3: Rx, Pin 5: Ground
Baud Rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

Configuration

8 data bits, 1 stop bit, no parity bits, flow control (RTS/CTS, none)
Trigger Outputs Polarity tip positive, sleeve ground
Maximum Current at 12 VDC 300 mA between all three triggers
Sequential Delay 250 ms
POWER REQUIREMENT
Consumption Maximum 170 W
DIMENSIONS
Height 5-7/8 inches (14.9 cm) including feet;
rack-mounting: 3 rack units without feet
Width Standard version 19-1/4 inches (49 cm)
Rack-Mount version 19 inches (48.3 cm)
No-Handle version 17-1/4 inches (43.8 cm)
Depth 15-1/4 inches (38.7 cm)
Weight (unpacked) 27 lb (12.3 kg)
AVAILABLE FINISH
Black

Audio/Video
Processors

Audio/Video
Receivers

Amplifiers

Integrated
Amplifiers

Monaural
Amplifiers